A tandem lift is a lift where two cranes work together to raise one load. It is used when a load is too heavy, too long, or too hard to reach for a single crane. Because both cranes share the weight, the lift needs careful planning, clear communication, and the right equipment.
Agri-Systems helps farmers and grain facility operators maintain reliable grain storage systems. Knowing when a job needs two cranes, and when one crane is enough, can help protect your equipment, your grain bins, and your crew.
How Is a Tandem Lift Different From Tailing a Load?
In tailing, one crane does the main lifting and a second crane only holds one end of the load. In a tandem lift, both cranes carry a real share of the weight from start to finish. Tailing is often used to turn a long load from lying flat to standing straight. Picture a tall tank lying on the ground. The main crane lifts the top end while the smaller crane holds the bottom end. Slowly the tank turns until it stands up. Then the tail crane lets go and the main crane finishes the job.
Because both cranes carry weight in a tandem lift, the plan has to be more detailed. Both cranes must lift, move, and stop together. If you are not sure which type your job needs, a lift planner can look at the load and tell you.
When Do You Need Two Cranes?
You need two cranes when one crane cannot lift the load safely on its own. There are four common reasons, and each one is easy to understand.
The Load Is Too Heavy for One Crane
If the load is heavier than what one crane can safely lift, you need a second crane. Every crane has a load chart that shows how much it can lift at each distance. The farther the load is from the crane, the less it can lift. A crane that handles a very heavy load up close may only handle a small part of that weight when the load is far away. When the chart says no, two cranes can share the weight so each one stays inside its safe limit.
The Load Is Too Long for One Pick Point
Very long loads often need two cranes because one pick point can bend or break them. If you lift a long beam in the middle, it may sag at the ends. Long concrete girders are a good example. A 2023 senior project from Cal Poly looked at tandem lifts of long span girders. It found that many lifting attempts had failed, and that each failure had its own reasons. It also showed that making, shipping, handling, and lifting a girder all add small problems that can show up later. Two lift points, held by two cranes, spread the weight along the length of the load and lower the chance of damage.
The Site Has No Room for One Large Crane
A site with tight space may only fit two smaller cranes. A very large crane needs a lot of room to set up and move. On a crowded site with buildings, pipes, tanks, or power lines, there may be no space for it. Two smaller cranes can often fit where one giant crane cannot. This is common on grain sites, where bins, support towers, and other equipment sit close together.
The Ground Cannot Hold One Large Crane
Soft or weak ground may not be able to hold the weight of one very large crane. A big crane puts a huge amount of weight on a small area. If the soil is soft, the crane can sink or even tip over. Two smaller cranes spread the weight over more ground. The ground should always be checked before a crane is chosen.
When Is a Single Crane a Better Option?
Yes, sometimes. If a bigger crane is available and fits on your site, one crane is often the simpler and safer choice. Two cranes mean more people, more rigging, and more things that can go wrong. A 2018 paper in Automation in Construction explains why this matters. The researchers wrote that lifting one object with two or more cranes carries more risk than a single crane lift. They also pointed out that in daily practice, the choice of crane type and crane operation often depends on the experience of the lift engineer. Their method compares crane options using cost, site, and environment, and it uses 3D simulation to test the lift before it happens. This takes much of the guessing out of the decision.
So the best question is not “Can we use two cranes?” It is “Do we have to?” Compare cost, safety, and space for every option. A larger crane may cost more to bring in, but a tandem lift needs two cranes, two operators, extra rigging, and more planning time. Sometimes the numbers favor one crane and sometimes they favor two.
Why Are Tandem Lifts Riskier Than Single Crane Lifts?
Tandem lifts are riskier because two machines have to act as one, and small mistakes get bigger quickly. There are a few main reasons for this. The first reason is that load sharing is not always equal. If one crane lifts a little faster than the other, it takes more of the weight. A crane that was safe at the start of the lift can be pushed close to its limit in the middle of it.
The second reason is that both cranes must move together. When the load swings or turns, each crane sees a different distance and a different angle. The load chart changes with every move, so the crew has to plan each step ahead of time. The third reason is that problems stack up. In a single crane lift, a small problem may stay small. In a tandem lift, a problem with one crane puts extra weight on the other. That extra weight can then cause a second problem.
The fourth reason is communication. Two operators cannot see everything the other one sees. They need one clear voice giving directions, and everyone must agree on the signals before the lift starts.
How Is a Tandem Lift Planned?
Planning a tandem lift involves several checks before the operation begins. The team must assess the load, select suitable cranes, inspect the ground, prepare the rigging, and establish a clear lifting sequence. The steps below are the ones most teams follow. This is true for a new bin and for grain bin repairs and storm damage restoration, where heavy parts often have to be lifted into place. The steps below are the ones most teams follow.
- First, the team finds the true weight of the load and where its center of gravity is. This tells them how much weight each crane will carry.
- Next, they choose the cranes and check the load charts. Many teams keep each crane well below its full rated limit during a tandem lift, because the weight can shift during the move. This gives a safety cushion.
- Then they check the ground and any structures under or near the cranes. The crane pads, mats, and soil must be able to carry the weight.
- After that, they plan the rigging. The slings, shackles, and spreader bars must match the load and the angle of each lift. Strong rigging is important here, because the rigging is what connects the two cranes to the load.
- Finally, they plan how the cranes will move together. This includes the path of the load, the speed of each crane, the signals everyone will use, and what to do if a crane has to stop. Many teams also run a meeting before the lift so that everyone knows their job. Bad weather, such as strong wind, can also stop a lift, so the plan should say what the wind limit is.
Who Works on a Tandem Lift?
A tandem lift needs a team, and each person has one clear job. The team usually includes a qualified person who writes the lift plan, a lift director who runs the lift on the day, two crane operators, riggers who attach the load, and a signal person who gives directions.
The lift director is the most important voice on site. Only one person should be giving orders during the lift. If two people shout different things, the operators can get confused. Everyone on the team should know who the lift director is before the cranes start to move.
Are Tandem Lifts Regulated?
Yes. In the United States, OSHA has extra rules for lifts that use more than one crane, and industry standards also give guidance. In most cases, a tandem lift needs a written plan made by a qualified person, and the people involved must be told about that plan before the lift. Rules can be different in each state or country, so always check the local requirements for your project.
Many companies also treat tandem lifts as critical lifts. A critical lift is one with a higher risk, such as a very heavy load, a lift that uses more than one crane, or a lift near people or important equipment. Critical lifts usually need a more detailed plan and more checks than regular lifts.
How Much Does a Tandem Lift Cost?
A tandem lift usually costs more than a single crane lift, but the price depends on the job. You pay for two cranes, two operators, extra rigging, extra setup time, and more planning. You may also pay for ground work, like mats or compacted pads, and for the trucks that bring the cranes in.
That said, the cheaper option on paper is not always the cheapest in real life. If a single large crane needs a long trip, a big space, and strong ground, two smaller cranes can end up costing less. The best way to know is to get a plan and a quote that compare both options.
Conclusion
A tandem lift is the right choice when a load is too heavy, too long, or too hard to reach for one crane. It also brings more risk, more people, and more planning than a single crane lift. The safest way to decide is to compare one crane and two cranes for your load, your site, and your ground. Then write a clear plan, pick a lift director, and make sure everyone knows their job before the cranes move.
Plan Your Next Tandem Lift With Agri-Systems
If you have a lift coming up, the team at Agri-Systems can help you decide between one crane and two, and plan the lift from start to finish. Tell us about your load and your site on our contact us page, and we will help you find the safest way to get it done.
Frequently Asked Questions
A tandem lift uses two cranes. If more than two cranes are used on one load, it is usually called a multi-crane lift.
Not always, but most companies treat it as one. Because two cranes carry one load, the risk is higher, so a detailed plan is almost always needed.
No. A tandem lift should never be done without a written plan. The plan keeps the cranes, the rigging, and the crew working together.
Yes. Two cranes with different lifting capacities can be used if the load share is calculated correctly and each crane is suitable for the part of the load it will carry. The lift plan must account for crane capacity, position, and movement to keep the operation within safe limits.
The lift must stop safely if communication between the crane operator and signal person is interrupted. Work should only resume after communication is restored and the operator receives and understands the correct signal. OSHA requires this under its crane signaling rules.
